Other Pipes, fittings, clips and hoses

This is the female half of a Hanson coupling. It has a 1/4" BSP connection.

Together with the male half, it provides a quick release hose coupling.

This is the male half of a Hanson coupling. It has a 1/4" BSP connection.

Together with the female half, it provides a quick release hose coupling.

This fitting can be screwed into the normal left-handed thread of a propane bottle to give a quarter inch BSP right-hand threaded outlet.

This fitting can be used to connect an installation (previously connected to a propane bottle) to allow connection to a refillable tank, via a quarter inch BSP thread.

This fitting screws directly onto a forklift bottle and provides a quarter inch BSP outlet.

This fitting is the type used for the outlet of a forklift bottle. It has a 3/8" BSP connection.

Together with the female half, it provides an easy release hose coupling fo LPG.

The hose is sold by the metre. So, make sure you order the right length.

Spring clips for securing the ends of 4mm LPG hose to rail, nozzle, pressure sensor and reducer.

The hose is sold by the metre. So, make sure you order the right length.

Spring clips for securing the ends of 5mm LPG hose to rail, nozzle, pressure sensor and reducer.

The hose is sold by the metre. So, make sure you order the right length.

Spring clips for securing the ends of 6mm LPG hose to rail, nozzle, pressure sensor and reducer.

The hose is sold by the metre. So, make sure you order the right length.

The hose is sold by the metre. So, make sure you order the right length.

The hose is sold by the metre. So, make sure you order the right length.

The hose is sold by the metre. So, make sure you order the right length.

Mainly used for Impco systems.

The hose is sold by the metre. So, make sure you order the right length.

This needle valve is used to turn off/on LPG flow.
It has quarter inch BSP inlet and outlet connectors - one male and one female.

This gate valve has quarter inch BSP inlet and outlet connectors and is used to turn off/on LPG flow.

This valve may come with a butterfly handle or a long handle (as shown).

5 mm metal T for manifold vacuum/pressure.

Can be used with 4mm hose, but needs easing in.

5 mm plastic Y for manifold vacuum/pressure.

Can be used with 4mm hose, but needs easing in.

10mm vapour Y piece - alloy.

This metal vapour Y has 15.5mm inlet/outlets.

Vapour control valve for single-point induction systems. The power valve fits in the hose between the reducer/vaporiser and the mixer and accommodates a step down from 16mm to 10mm hose.

Vapour control valve for single-point induction systems. The power valve fits in a 16mm LPG hose between the reducer/vaporiser and the mixer.

This plastic power valve has a 17mm inlet and two 17mm outlets and is used where a single vaporiser feeds twin mixer inlets.

This plastic power valve has a 19mm inlet and two 12mm outlets and is used where a single vaporiser feeds twin mixer inlets.

In order to connect a 6 mm pipe to the outlet valve on a 4-hole tank, you will need to flare the end of the pipe and use a flare nut.
These flare nuts are designed to fit outlet valves with a large thread (12 mm).
If you are buying a set of valves from our shop, this flare nut will fit.

In order to connect an 8 mm pipe to the outlet valve on a 4-hole tank, you will need to flare the end of the pipe and use a flare nut.
These flare nuts are designed to fit outlet valves with a large thread (12 mm).
If you are buying a set of valves from our shop, this flare nut will fit.

In order to connect a 6 mm pipe to the outlet valve on a 4-hole tank, you will need to flare the end of the pipe and use a flare nut.
These flare nuts are designed to fit outlet valves with a small thread (10 mm).
If you are buying a set of valves from our shop, this flare nut will be too small.

Some older 4-hole tank outlet valves have a smaller thread than the current valves.

This adapter converts the small thread outlet to a large thread that can be used with the larger flare nuts (6 or 8 mm).

The hose is sold by the metre. So, make sure you order the right length.

This vent hose can be extended from 35 to 96cm.

In order to vent gases to the outside of the vehicle, cut a 30mm hole in the floor of the vehicle, apply a small amount of sealant and insert a bulkhead fitting. Slide the vent hose onto the fitting and secure it.

This product comprises 2 x bulkhead fittings.

This fitting has a 6mm pipe stub and 6mm olive and squeeze nut.

This fitting has a 6mm pipe stub and 8mm olive and squeeze nut.

This fitting has a 8mm pipe stub and 8mm olive and squeeze nut.

Click clips for securing the ends of 10mm LPG hose to rail and reducer or reducer and water T.

This fitting eases the problem of fitting an 8mm pipe onto a Tomasetto 30° toroidal tank.

Where 2 tanks are installed on a vehicle, it is essential to avoid back-filling one tank from the other through the outlet valve. This can be achieved using a non-return T. One tank is connected to each arm of the T and the leg feeds the engine.
This T is for 6 mm copper pipe.

If you have 2 tanks and want to fill them from a single filler, you will need a T.
This T is for 6 mm copper pipe.

If you have 2 tanks and want to fill them from a single filler, you will need a T.

This T is for 6 mm copper pipe and, because of its size and style of compression fittings, is ideal for use with poly pipe (where the fittings have relatively short stubs).

Where 2 tanks are installed on a vehicle, it is essential to avoid back-filling one tank from the other through the outlet valve. This can be achieved using a non-return T. One tank is connected to each arm of the T and the leg feeds the engine.
This T is for 8 mm copper pipe.

If you have 2 tanks and want to fill them from a single filler, you will need a T.
This T is for 8 mm copper pipe.

A selection of parts for connecting copper pipes, comprising:
1 x joiner 8mm x 8mm
1 x joiner 8mm x 6mm
2 x squeeze nuts 6mm (1 long, 1 short)
2 x squeeze nuts 8mm (1 male, 1 female)
2 x olives 6mm
2 x olives 8mm

This is suitable for use between the tank and the engine bay for most vehicles.
Engines over 190 bhp are usually best on 8mm pipe.

This is suitable as a fill pipe for most vehicles.
If you have twin tanks, you will probably need more than 3.5m

This is suitable for use between the tank and the engine bay for engines over 190 bhp.
If you use this as a feed pipe, you will probably need 6mm-8mm adaptors for the multivalve, filter/shut-off valve and reducer (these are sold as a separate product).
It can also be use as a fill pipe where you need more than 3.5m.

This pack contains 4 adaptors for use when connecting 8mm pipe to multivalves, filter/shut-off valves and reducers. It also contains a connector that can be used to screw the filter/shut-off valve directly to the reducer.

10 olives for 6mm copper pipe
plus
5 olives for 8mm copper pipe.

Fill pipes and feed pipes must be secured to the vehicle at intervals no more than 600mm using metal clips.
This pack contains 20 clips and screws, suitable for securing plastic-coated copper pipe.

This can be screwed into a multivalve outlet or shut-off solenoid valve to allow connection to 8mm pipe.

Used mainly for fitting a shut-off valve directly to a vapouriser. M10 threads at each end.

For joining 2 lengths of 6mm copper pipe.

For joining 6mm to 8mm copper pipe.

For joining 2 lengths of 8mm copper pipe.

6mm in-line non-return valve.

10 Jubilee clips, 16 to 25mm. Suitable for water or gas hoses with an internal diameter of 16 to 19mm.

10 Jubilee clips, to 16mm. Suitable for water or gas hoses with an internal diameter of 8 to 12mm.

Very small jubilee clips (x10) for 6 to 11mm hose.

For joining 8mm to 10mm copper pipe.